meta data for this page
  •  

Differences

This shows you the differences between two versions of the page.

Link to this comparison view

Both sides previous revisionPrevious revision
Next revision		Previous revision
hw:server:dellr720 [2024/11/12 11:58] – niziakhw:server:dellr720 [2025/12/11 08:52] (current) – niziak
Line 1: Line 1:
 ====== Dell PowerEdge R720 ====== ====== Dell PowerEdge R720 ======
  
 +[[https://i.dell.com/sites/csdocuments/Shared-Content_data-Sheets_Documents/ja/jp/Dell-PowerEdge-R720Technical-Guide-2018Jun.pdf]]
 +
 +  * MB:
 +    * Intel C602 Chipset
 +    * Manufacturer: Dell Inc. / Product Name: 0020HJ /Version: A02
 +    * 2 x LGA2011 socket
 +    * MAX CPU Xeon E5-2697v2 12 core @ 2.7GHz (30MB cache)
 +  * CPU:
 +    * 2 x Intel(R) Xeon(R) CPU E5-2650 v2 @ 2.60GHz (max speed 3.4GHz) 8C/16T IvyBridge based (20MB cache)
   * LSI SAS2 MPT Controller SAS2308 (PCI ID 0x2:0x0:0x0)   * LSI SAS2 MPT Controller SAS2308 (PCI ID 0x2:0x0:0x0)
     *  mpt2sas_cm0: LSISAS2308: FWVersion(20.00.07.00), ChipRevision(0x05), BiosVersion(07.27.01.01)     *  mpt2sas_cm0: LSISAS2308: FWVersion(20.00.07.00), ChipRevision(0x05), BiosVersion(07.27.01.01)
 +  * BIOS Information
 +    * Vendor: Dell Inc.
 +    * Version: 2.9.0
 +    * Release Date: 12/06/2019
 +
 +
  
 ===== boot speedup ===== ===== boot speedup =====
Line 40: Line 55:
     * ''Enable Alerts''     * ''Enable Alerts''
     * Setup ''Alerts Filter''     * Setup ''Alerts Filter''
-    * Enable checkmark in column ''Remote System Log''+    * Enable checkmark in column ''Remote System Log''. NOTE: there are multiple pages of alerts. There is no need to click ''apply'' before changing page. 
 +    * test remote syslog using ''Test Event'' at bottom of page 
 + 
 + 
 +===== ENERGY_PERF_BIAS ===== 
 + 
 +Despite of BIOS setting to ''performance'' kernel changes it during boot: 
 + 
 +<code bash> 
 +kernel: ENERGY_PERF_BIAS: Set to 'normal', was 'performance' 
 +</code> 
 + 
 +[[https://support.scc.suse.com/s/kb/Boot-log-displays-ENERGY-PERF-BIAS-Set-to-normal-was-performance?language=en_US]]: 
 + 
 +  The EPB MSR (ENERGY_PERF_BIAS Machine Specific Register) is a feature of some Intel CPUs.  It can be set to a value from 0-15 to tell the CPU (microcode) whether it should prefer performance (0) over powersave (15) power management. 
 +  Intel has observed that on many systems after the hardware platform firmware (BIOS/UEFI) finishes initialization, the initial EPB value is 0 ('performance').  While on some systems this is intentional, on others it is due to the system firmware (UEFI/BIOS) not properly initializing the value of the EPB MSR.  Intel implemented a fix in the Linux kernel EPB initialization code to set the EPB to value of 6 ('normal') when the Linux kernel boots.  After the kernel finishes loading a proper EPB value can then be selected.  Unfortunately, this causes a bit of an inconvenience on systems where the system firmware deliberately set EPB to 0 as they will need to set the value back to 0 after Linux loads.  However, other systems (where the EPB value is 0 due to not having been properly initialized) have a higher power consumption than intended/desirable which can cause issues for systems operating from battery power (standby/ups power, or laptops). 
 + 
 +ENERGY_PERF_BIAS: 
 +  * 0 - performance (140W) 
 +  * 3 - (140W) 
 +  * 4 - balance-performance (126W) 
 +  * 6 - normal (126W) 
 +  * 8 - balance-power 
 +  * 15 - power (max power saving) (126W) 
 +  
 +<code bash> 
 +apt instal linux-cpupower 
 + 
 +# x86_energy_perf_policy 
 +cpu0: EPB 6 
 +cpu1: EPB 6 
 +... 
 +cpu30: EPB 6 
 +cpu31: EPB 6 
 + 
 +# x86_energy_perf_policy balance-performance 
 +</code> 
 + 
 +<code bash> 
 +ipmitool sensor reading 'Pwr Consumption' 
 +</code>